
ROS Remote Optical LED Sensor - Monarch Instrument
The versatile ROS-W (with tinned wire termination) and ROS-P (with 1/8″ phone plug termination) are threaded stainless steel remote optical sensors with a visible red LED light source. Four models to choose from! All include cable, mounting bracket, and 12 inches of T-5 Reflective Tape.
The ROS-P and ROS-P-25 will work directly with all Monarch Handheld Tachometers, Deluxe Nova-Strobe models (DA+, DB+, dax, dbx) and Phaser Strobe (PB, pbx) Stroboscopes. A sensor power supply (SPS, SPSR) with BNC output is available for those applications that require a separate power source for the sensor.
美国蒙那多ROS-P和ROS-W光电转速传感器价格|厂家|使用方法
ros-p 型:远程光学 led 传感器,带 8 英尺电缆,带 1/8 英寸电话插头端接、安装支架和 12 英寸 t-5 反光胶带。 ros-p25 型:与 ros-p 相同,但使用 25 英尺电缆。 产品都包括电缆、安装支架和 12 英寸的 t-5 反光带。
美国蒙那多ROS-P/ros-p-25光电转速传感器_上海路阳仪器转速测 …
美国蒙那多ros-p光电转速传感器通过在被测物体上贴反光条,利用光电原理来输出标准的ttl转速信号。 TTL转速信号可通过ACT系列 转速表 显示出转速,也可用于其他工业控制及自动化。
美国蒙那多ROS/ROS-P-25/ ROS-HT-W-25光电转速传感器 原装
ROS-P-25 传感器,7.6米长连接线(3.5mm立体声接头) ,30cm T-5反光条,安装支架 光电转速传感器通过在被测物体上贴反光条,利用光电原理来输出标准的TTL转速信号。
Monarch ROS-P-256180-057-25 Sensors with 25 foot cable ROS-P …
The ROS-W (Remote Optical Sensor with tinned wire termination) and ROS-P (Remote Optical Sensor with 1/8" phone plug termination) are threaded stainless steel remote optical sensors with a visible red LED light source.
美国蒙那多转速传感器ROS的说明书-上海峰志仪器有限公司
2024年6月8日 · 美国蒙那多转速传感器ros-w/ros-p能够检测由t-5反光贴纸组成的目标的反射脉冲,距离旋转物体36英寸[1米],角度45度。 对于大多数应用,应在旋转物体的清洁区域使用½”[12mm]的方形反光带(T-5)。
Monarch ROS Remote Optical Sensor
Monarch Remote Optical Sensor (ROS), Wired or Phone Plug Connection with Green On Target Indicator. Reads 0-250,000 Revolutions Per Minute (RPM) includes cable, mounting bracket and 12 inches of T-5 reflective tape .
ROS-P光电传感器 ROS-W光电传感器 蒙那多MONARCH转速传感器 ROS
ros-w为镀锡裸线,棕色接电源+,蓝色接电源-,黑色接信号。 ros-p为3.5mm音频接头,剪掉接头就是ros-w. ros光电转速传感器简介: 测量范围:1-250000rpm. 测量距离:1m以内,倾角45°内. 温度范围:-10-70° 供电电压:3-15v. 信号输出:ttl. 连接线长度:2.4m或加长. 尺寸 ...
美国蒙那多Monarch ROS光电转速传感器 ROS-P - 百度爱采购
美国蒙那多Monarch ROS光电转速传感器 ROS-W和ROS-P:传感器外壳由带螺纹的不锈钢制成,方便固定,采用红色LED光源,采集有效信号后尾部绿色LED灯亮起,表示测量有效,量程大,应用。